Author Topic: Removing Tabs for NES Cases: Easiest Way?  (Read 338 times)

January 05, 2013, 08:01:43 PM
Read 338 times

wingzrow

  • ***
  • Information Offline
  • Full Member
  • Posts: 197
    • Email
I've tried modifying UGCs for NES cases with an exacto knife AND a dremel. Neither work. An exacto knife is much too slow, and a dremel is too noisy,messy, & it melts the case.

How do you guys do it? What would be the easiest way to do a clean job?

January 05, 2013, 09:03:54 PM
Reply #1

mojoeskateco

  • *****
  • Information Offline
  • Hero Member
  • Posts: 536
    • Email
Dremel works great for me.  It does leave a bit of a mess but you can clean it up with an exacto. 


January 05, 2013, 09:06:44 PM
Reply #2

TyrannicalFascist

  • </StarWarsNerd> Who can't wait!
  • ******
  • Information Offline
  • Dedicated Member
  • Posts: 1123
  • Boggle!?
    • Email
I just go at it with an end cutter. Takes some patience, but gets the job done nicely.
Click Here for my Video Game Covers
Switch - Tyrannicus | 3DS - 0130-1810-3706
Wanted GB bootlegs: Spiritual Warfare, Sonic 8 (rumble), Mario DX (GBA), Donkey Kong II (GBA)

January 05, 2013, 09:10:17 PM
Reply #3

segamer

  • I'm going to make you cry, the way I cried, when my daddy died.
  • *
  • Information Offline
  • Ultra Member
  • Cover Admin
  • Posts: 2687
    • Email
I use convexed toe nail clipper. I took out the center piece of the clippers. And use pliers to squeeze.

January 05, 2013, 09:23:47 PM
Reply #4

Zeanhaven

  • **
  • Information Offline
  • Jr. Member
  • Posts: 77
    • Email
i used a razorblade with ducktape at the end to make a handle and slide it, thats what i did

January 05, 2013, 09:28:26 PM
Reply #5

Beastman1975

  • *****
  • Information Offline
  • Hero Member
  • Posts: 660
ive used a dremel with the cutting blade . just have to take you time and not sit in one place to long, cut a bit let cool cut a bit  , so as not to melt the plastic  also i have a set of these but they dont cut as close http://www.amazon.com/Channellock-358-8-Inch-Cutting-Plier/dp/B00004SBD8/ref=sr_1_4?s=hi&ie=UTF8&qid=1357439197&sr=1-4&keywords=nail+cutter

January 06, 2013, 12:40:33 AM
Reply #6

SasoriSoren

  • ****
  • Information Offline
  • Sr. Member
  • Posts: 339
    • The Portlandian
    • Email
I just use my Dremel with a 1-inch Wood and Metal cutter. It lays flat against the plastic of the case getting a super close cut without any real effort.

January 06, 2013, 09:08:27 AM
Reply #7

tiktektak

  • Live to die
  • *
  • Information Offline
  • Omega
  • Cover Admin
  • Posts: 4112
A dremel works fast and easy. It makes a mess though. I built myself a little working station from some big cardboard boxes.
2 + 3 = 23

January 06, 2013, 10:42:47 AM
Reply #8

SasoriSoren

  • ****
  • Information Offline
  • Sr. Member
  • Posts: 339
    • The Portlandian
    • Email
I just found a table on the curb a few months ago that was pretty worn and use that. The dremel doesn't make too much mess though, especially once you are in a rhythm. I can bust out 20 cases in about 10 minutes with it.

January 06, 2013, 11:29:16 AM
Reply #9

sniperlobster

  • ***
  • Information Offline
  • Full Member
  • Posts: 227
    • Email
I use an Exacto knife to just loosen up the tabs then grab a pair of pliers and pull them right off...I've done about 20 cases so far because I ran out from other games and only ruined maybe one. It does take a little longer than a dermal but it gets the job done

January 06, 2013, 01:09:23 PM
Reply #10

larryinc64

  • Custom Title
  • *
  • Information Offline
  • Omega
  • Cover Guru
  • Posts: 3807
  • Motament
    • Motament (My Art)
If you wait, Seymor Onion is developing cases for NES games with no modification required.
http://www.thecoverproject.net/forums/index.php?topic=10153.210